To change the TFTP setting on the Cisco model , and phones used in your ShoreTel Sky phone system, use the following instructions: Press the "Settings" button on the telephone. Category: home and garden smart home.
Verify the Network Setup. Activation Code Onboarding for On-premises Phones. Enable Autoregistration for Phones. Install the Cisco IP Phone. Set Up the Phone from the Setup Menus. Configure Network Settings. Verify Phone Startup. How does a Cisco phone work? How do I connect my IP phone? IP Phone Setup Guide. Plug the phone in and connect it to your network. How do I set up an IP phone? How do I connect my Cisco phone to my network?
How do I connect my Cisco phone to the Internet? Enable the phone's Wireless Connection. Power ON the phone using the power adapter that came with the device. Activation codes provide a simple method for provisioning and onboarding phones without requiring an administrator to collect and input the MAC Address for each phone manually. First, disconnect the Ethernet cable from the computer and attach it to the network port on the back of your phone.
Next, use the Ethernet cable included with your phone to connect the access port on the back of your phone to your desktop computer. Your Cisco IP Phone now shares a network connection with your computer. They can register phones securely back to the corporate phone system.
To power the phone, you will need a power supply or power injector. See External Device Use for more information. In some cases, hum can be reduced or eliminated by using a local power cube or power injector. These environmental and hardware inconsistencies in the locations where Cisco Unified IP Phones are deployed means that there is not a single headset solution that is optimal for all environments.
We recommend that customers test headsets in their intended environment to determine performance before making a purchasing decision and deploying en masse. Beyond the physical, mechanical and technical performance, the audio portion of a headset must sound good to the user and to the party on the far end. Sound quality is subjective and Cisco cannot guarantee the performance of any headsets. However, a variety of headsets from leading headset manufacturers have been reported to perform well with Cisco Unified IP Phones.
Press the Headset button on the phone to place and answer calls using the headset. Use these buttons to adjust the ear piece volume and to mute the speech path from the headset microphone. See the wireless headset documentation for information about connecting the headset and using the features. By default, the Wireless Headset Hookswitch Control option is disabled. Cisco recommends the use of good quality external devices, such as speakers, microphones, and headsets that are shielded screened against unwanted radio frequency RF and audio frequency AF signals.
Depending on the quality of these devices and their proximity to other devices, such as mobile phones or two-way radios, some audio noise may still occur. In these cases, Cisco recommends that you take one or more of the following actions:.
Route the external device cables away from the source of the RF or AF signals. Use shielded cables for the external device, or use cables with a better shield and connector. Apply ferrites or other such devices on the cables for the external device. Cisco cannot guarantee the performance of the system because Cisco has no control over the quality of external devices, cables, and connectors. The system performs adequately when suitable devices are attached with good quality cables and connectors.
Before you install a phone, even if it is new, upgrade the phone to the current firmware image. Before using external devices, read External Device Use for safety and performance information. Remove the hookswitch clip see Handset from the cradle area. The following figure and table show how to connect your phone. You can customize the button templates for the Cisco Unified IP Phone Expansion Module to determine the number of line appearances and speed dial buttons. See Phone Button Templates for details.
When you initially add the phone to Cisco Unified Communications Manager, by selecting one of the following entries in the Module 1 or Module 2 fields, and choosing the appropriate expansion module firmware:. When you initially add the phone to Cisco Unified Communications Manager, you can choose Button Line Expansion Module in the Module 1 or Module 2 fields and then choose the appropriate expansion module firmware.
The Find and List Phone page appears. The Find and List Phone window displays showing a list of the phones that match your search criteria. In the Firmware Load Information section, there are two fields that specify the firmware load for Modules 1 and 2.
You can leave these fields blank to use the default firmware load. Use the Phone Button Template Configuration to configure the buttons. Cisco Unified Communications Manager includes several default phone button templates. When adding phones, you can assign one of these templates to the phones or create a new template. To configure the 48 additional buttons, follow these steps:. When you place the phone on a desktop surface, you can adjust the tilt height to several different angles in 7.
You can also mount these phones to the wall by using the footstand or by using the optional locking wall mount kit. To adjust the footstand, push in the footstand adjustment button and adjust the tilt.
The lock connects to the security slot on the back of the phone, and the cable can be secured to a desktop. The security slot can accommodate a lock up to 20 mm. Compatible laptop cable locks include the Kensington laptop cable lock and laptop cable locks from other manufacturers that can fit into the security slot on the back of the phone. See the following figure.
0コメント